^$1289Basic       
Geenbellon Turbine Flow Meters can measure fluid in a closed pipe system and display flow rate and total flow in Volume unit in same time. the theory of this type flow meter is that the flowing medium engages a vaned rotor causing it to rotate at an angular velocity proportional to the flow rate Within the turbine flow meter. The pickup coil senses the spinning motion of the rotor through the housing and converts it into a pulsing electrical signal. Totalling the pulsing electrical signal directly yields to the total flow, while the frequency is linearly related to the flow rate.
The flow meter is featured that it is tough for an applications in severe condition with high accuracy, light weight, interface flexible, anti-abrasion, and anticorrosion. So, it is applied widely in industry, Municipal, Agriculture, Military engineering. The production introduced as below is one of all models.

Features
*> Standard ANSI Flange Connection, Easy to install and uninstall in a pipe line and easy to find the mating material. .
*> The Max working pressure ANSI 2500# flange 6170PSi (42.5MPa)
*> the Tungsten Carbide/Ceramic hybrid ball bearings & shaft extend much longer of the usage life of Flow meter
*> High accuracy and High accuracy repeatable measurement
*> Rugged structure  to withstand continual rig up/down
*> Most economical solution for flow measurement applications
*> High frequency digital output easy interface with other digital equipment.
*> Symmetrical Bi-directional Design
*> Wide temperature & Pressure Ranges
*> Wide flow range (Typically 15:1-100:1)
*> Minimum maintenance
*> Long service life, even in severe applications

Application
@ Water & dirty water measurement
@ Disposal wells
@ fuel and feed water
@ liquid fertilizer
@ fuel and chemical measurement in many field.
@ liquid propane
@ mining and leaching

---

Medium for Measured

---

Technical Parameters
  Accuracy: +/- 1.0;  +/- 0.5%
  Repeatable: +/- 0.05%
  End Connection: ANSI SS/CS 300# Flange
  Working Pressure: Max.740  PSi (5.10MPa) @ 20℃
  Working Tempreture: -65 to 450 ℉ (-55 to 232 ℃)
  Pickup Connection: AN3106A-10SL-4S/3S (MIL STD Two/Three Holes Plug)
  Magnetic Sensors: 1ea/2ea (Optional) Provide the STD signal for loacal/romote diaplay equipments.
@Structure of Internal repair Kits: Y Serial
@Material
  Body: Stainless Steel 304/316L (Depend on the fluid measured)
  Vane: 304/316L
  Shaft&Bearing: Tungsten Carbide
@Pickup:
  Body: 300 Serial Stainless Steel
  Compliance
*CSA Certified Harzardous Locations Class I, Group A,B,C,D,Div.1
*NACE MR01-75(NACE traceability available on request.)

---

Meter Size Selection
Geenbellon Turbine Flow Meters bore size selection do not depend on size of the pipe-line the meter will be mounted in, it must be decided on the instantaneous flow rate in the pipe-line.

Note:  1.The data above is based on Water-Calibration.
         2. The best linear flow range for Non-lubricating Liquid is at upper 60% of the standard range.
         3. Consult factory for engineering assistance when the viscosities of the liquids measured greater than 5 centistokes.

---

ANSI B16.5 Flanges Selection

---

Model No. Definition

Note：①. Model No. is composed of letters plus numbers regularly. ②. There are not conflicts between the various elements of the model cannot be allowed. For example, the selection of high temperature turbine body in previous position, the following position is the choice of standard temperature pickups. As to detailed information, please refer to the related section in manual or enquires with the manufacturers. ③. When you select more than 1 pickup and flow analyzer to work at the same time, in the No. 9 and No. 10 position, express method is flow analyzer model & installation mode + ... ④. In order to save costs, Geenbellon assists the user make a basic options selection on flow analyzer and flow computer under common conditions. If having special needs, marked ( ) with the corresponding position of the model, while the technical details is required to list in the technical agreement, quotation or contract.

---

Installation Diagram


Related Document
GIL-Products-List      Model-Selecting-Sheet

Word Explanation
STD = Standard Type || ACC = Accuracy || Size = Nominal Bore Size || End = End Connction Size || Flow = Flow Range || GPM = Gallon Per Minute || M3.H = Cubic Meter Per Hour  || WT = Weight in Kilogram
RFSS = Stainless Steel Flange w/Raised Face, the size of flange is 150#, 300#, 600#, 900#, 1500#, 2500#
RFCS = Carbon Steel Flange w/Ring Joint, the size of flange is 600#, 900#, 1500#, 2500#
RJSS = Stainless Steel Flange w/Raised Face, the size of flange is 150#, 300#, 600#, 900#, 1500#, 2500#
RJCS = Carbon Steel Flange w/Ring Joint, the size of flange is 600#, 900#, 1500#, 2500#